Multi-turn actuators

Non-Intrusive multi-turn actuators for open-close duty with integral controls AUMATIC Type SA 07.2 – SA 16.2 with AC 01.2 Version according to wiring diagram TPC A-0A1-1C1-A000 TPA 00R100-3I1-000 Type of duty: short-time duty S2-15 min Output speeds of 4 to 180 rpm at 50 Hz supply 3-ph AC motor in insulation class F, with motor protection by three thermoswitches placed in the windings Motor without terminal box, internal connection via plug/socket connector Anti-condensation heater in switch compartment, internal supply Electronic absolute encoder for position and torque sensing Handwheel does not rotate during motor operation, with output contact for manual operation Valve attachment according to EN ISO 5210 Connection between actuator and controls via plug/socket connector Reversing contactors mechanically and electrically interlocked Local controls with operation mode switch, 4 push buttons, 6 indication lights, Bluetooth interface and plaintext display for programming, status, position and fault indication Four inputs OPEN - STOP - CLOSE - EMERGENCY 24 V DC galvanically isolated via opto-isolator Six freely programmable contacts for ou

Multi-turn actuators for open-close duty type SA ...   Version according to terminal plan KMS TP 110/001: Type of duty: short-time S2 - 15 min Output speeds of 4 up to max. 180 rpm at 50 Hz supply, depending on the size 3-ph AC motor in insulation class F, with motor protection by three thermoswitches placed in the windings Motor (up to SA 16) without terminal box, internal connection via plug/socket connector Mechanical limit switching without auxiliary voltage for end positions CLOSED/OPEN Tripping torque without auxiliary voltage for closing/opening direction adjustable at calibrated torque dial and directly readable in daNm Mechanical blinker transmitter for running indication Anti-condensation heater in switch compartment Handwheel for manual operation which does not rotate during motor operation Valve attachment according to ISO 5210 Connection actuator – external controls via plug/socket connector Ambient temperature – 25 °C to +80 °C, enclosure protection IP 67, corrosion protection KN (suitable for atmosphere with low pollutant concentration) Finish coating: Two-component iron-mica combination, colour: silver-grey (similar to

By combining the multi-turn actuators SA with the worm gearboxes GS, they are turned into electric part-turn actuators for higher torque requirements. These combinations supplement the part-turn actuator ranges SG and ASR whose torque ranges are limited to 1,200 Nm or 500 Nm, respectively.  Design features: Torque range from 250 Nm to 675,000 Nm Swing angles up to 100° Operating times for 90 Â° from 9 s to 780 s adjustable end stops self-retaining Handwheel for manual operation Ambient conditions: High enclosure protection High quality corrosion protection Wide ambient temperature ranges Options: Swing angles > 100° or multi-turn (without end stops) Interfaces: Electrical connection via AUMA plug/ socket connector (optionally terminals) Cable entries in different versions Output drive types according to ISO standard

The modulating actuators of the SAR range are rated for intermittent duty S4 - 25 %. Special versions for S4 - 50 % and S5 - 25 % are also available. Actuators of type range SAR 07.2 – SAR 16.2 can be combined with various controls: From simple OPEN-CLOSE control to the micro-controlled version with logging of operating data or fieldbus interface Design features: Torque range from 15 Nm to 4,000 Nm Modulating torque range from 15 Nm to 1,600 Nm Max. number of starts 1,200 c/h Output speeds from 4 to 45 rpm Limit and torque sensing Available with 3-ph AC, 1-ph AC motors Handwheel for manual operation Ambient conditions: High enclosure protection High quality corrosion protection Wide ambient temperature ranges Options: Switches in tandem version Remote position transmitter Magnetic limit and torque transmitter Mechanical position indicator Interfaces: Electrical connection via AUMA plug/socket connector (optionally terminals) Cable entries in different versions Output drive types according to&nb

Multi-turn actuators for modulating duty type SAR ...   Version according to terminal plan KMS TP 100/001:   Type of duty: intermittent S4 - 25%; max. 1200 c/h Output speeds of 4 to max. 45 rpm at 50 Hz supply 3-ph AC motor in insulation class F, with motor protection by three thermoswitches placed in the windings Motor (up to SA 16) without terminal box, internal connection via plug/socket connector Mechanical limit switching without auxiliary voltage for end positions CLOSED/OPEN Tripping torque without auxiliary voltage for closing/opening direction adjustable at calibrated torque dial and directly readable in daNm Anti-condensation heater in switch compartment Handwheel for manual operation which does not rotate during motor operation Valve attachment according to ISO 5210 Connection actuator – external controls via plug/socket connector Ambient temperature – 25 °C to +60 °C, enclosure protection IP 67, corrosion protection KN (suitable for atmosphere with low pollutant concentration) Finish coating: Two-component iron-mica combination, colour: silver-grey (similar to RAL 9007) Options: Corrosion protection KS for in

The "small" electric globe valve actuator range with integral controls. All parameters are directly set at the actuator. The controls contain switchgears, power supply unit, interface to the DCS. The component automatically switches the actuator off, once the valve end position is reached, motor overheating is detected or a torque overload has occurred. All housing parts are made of aluminium. For this reason, the actuators are lightweight devices. The actuators are rated for short-time duty S2 - 15 min. Design features: Torque range from 10 Nm to 100 Nm Speeds from 0.6 to 22 rpm Max. 16 turns per stroke Limit and torque seating Variable speed, brushless motor Handwheel for manual operation Ambient conditions: High enclosure protection High quality corrosion protection Wide ambient temperature ranges Options: Profibus DP interface Local controls mounted separately from the actuator

Tightening torCross sectionsOutput speedType 2 2.0 Nm0.5 ¤ 16 mm4 ¤ 22SAEx 25.1 SAREx 25.1 2 3.5 Nm2.5 ¤ 35 mm32 ¤ 90 2 1.2 ¤ 2.4 Nm4 ¤ 16 mm4 ¤ 22SAEx 30.1 SAREx 30.1 2 4.0 ¤ 5.0 Nm10 ¤ 35 mm32 ¤ 45 2 6.0 ¤ 12 Nm16 ¤ 70 mm63 ¤ 90 2 1.2 ¤ 2.4 Nm4 ¤ 16 mm4 ¤ 5.6SAEx 35.1 2 4.0 ¤ 5.0 Nm10 ¤ 35 mm8 ¤ 22 2 6.0 ¤ 12 Nm16 ¤ 70 mm32 ¤ 45 2 4.0 ¤ 5.0 Nm10 ¤ 35 mm4 ¤ 11SAEx 40.1 2 6.0 ¤ 12 Nm16 ¤ 70 mm16 ¤ 32

Explosion-proof multi-turn actuators for OPEN-CLOSE duty type SAExC ... with integral controls AUMA MATIC AMExC according to ATEX directive 94/9/EC    Version according to wiring diagram MSP E310KC3--FF8EC   KMS TP 210/001 Explosion protection II2G EEx de IIC T4 according to EN 50 014, 50 018, 50 019 Type of duty: short-time S2 - 15 min Output speeds of 4 to 180 rpm at 50 Hz supply 3-ph AC motor in insulation class F, with motor protection by three PTC thermistors placed in the windings, thermistor tripping device in the controls Motor without terminal box, internal connection via plug/socket connector Counter gear limit switching for end positions CLOSED/OPEN Tripping torque for closing/opening direction adjustable at calibrated torque dial and directly readable in daNm Anti-condensation heater in switch compartment Handwheel for manual operation, which does not rotate during motor operation Valve attachment according to ISO 5210 Connection actuator – controls via internal plug/socket connector Reversing contactors mechanically and electrically interlocked Local controls with push-buttons OPEN-STOP-CLOSE and lockable operation mo