Buschjost proportional valve and electronic Norgren Motorised valve Series 82880

Characteristic data
Valves
Part Number -Wert **
Nominal Diameter Connection size Operatng pressure * k Weight
v
s
1) 3
(motor  (Base m
) (mm) min. (bar)                      max. (bar)   /h) (kg)
8288500.96XX ¨ Cartridge ¨C0. 10 1.1 0.7
8288200.96XX 15 G 1/2 ¨C0. 10 1.1 0.9
2)
4.4 1.6
8288300.96XX 20 G 3/4 ¨C0. 6
2)
4.4 1.6
8288400.96XX 20 G 1 ¨C0. 6
1) 2)
 See motor drives for motor Cat no  and power supply  Operating pressure increases to 10 bar for 9624 and 9651
Characteristic data
Motor
Standard
Frequency Power consump- Protection  Torque Operating  Wiring dia- Motor Cat-No.
Motor type voltage
 
tion  class time  through gram
Tolerance
1)
!à10
[Hz] [W] [Ncm] 90!a6
[V]
DC motor 24  -   1.5 IP 54 120 10 - 14 s 01 9615.02400
DC motor 24  -   1.5 IP 54 120 10 - 16 s 02 9650.02400
DC motor 24  -   2.1 IP 54 120 10 - 16 s 03 9657.02400
Synchronus motor 24 50 3.0 IP 54 120 10 s 04 9636.02450
Stepping motor 24 2) 5.0 IP 54 120 10 s 05 9638.02400
3)
DC motor 24  -   2.0 IP 54 200 13 s 01 9624.02400
3)
DC motor 24  -   2.5 IP 54 200 13 - 16 s 02 9651.02400
1)
3)
 Operating time depends on operating pressure  Only in conjunction with G 3/4 and G 1
2)
 Nominal stepping frequency 200 Hz
Note! All motor drives fulfil the requirements of the generic standards for electromagnetic compability
(EN 61000-6-3:2007 and EN 61000-6-2:2006) to Directive 2004/108/EC.
Limit switch service life >100,000 cycles
Further technical data for DC motor Cat.no. 9615, 9624
Motor with feedback potentiometer for servo-amplifier
Feedback potentiometer
Resistor:      1 k|
Resistor tolerance:     !à  20
Max wiper current:     1mA
Power rating:     0,1 W
Only part of the potentiometer!ˉs range is used
Further technical data for DC motors Cat Nos 9650 and 9651
Drives with integrated position controller
The set point input can be set to the required signal range with the 2 jumpers.
Power supply residual ripple:    max. 1,2 V
ss
Set point input:     0 ¨C 10     J1, J2 not inserted
      0 ¨C 20 m   J1 inserted,J2 not inserted
      4 ¨C 20 m   J1, J2 inserted
Input signal ripple:     max. 40 m V  with voltage signal
ss
      max. 0,08 mA  with current signal
ss
Input resistance:     200 k|? with voltage signa
      500 k|? with current signa
Auxiliary voltage for external potentiometer:  12 V  !à 3
      max. 10 mA
IMPORTANT!  Brief interruptions in the power supply e.g.caused, by it being switched by an electromechanical relay,
can cause the electronics to malfunction.

Motor design Motor life  Recommended pulse current
(running time) duration during reversal in direction of
rotation
DC motor  9615 500 h > 100 msec 600 msec
DC motor  9624 500 h > 100 msec 250 msec
DC motor  9650, 9657, 9651 500 h  -   -
Synchronous
9636 1000 h > 100 msec 40 msec
motor
Stepping motor  9638 1000 h Stepping frequency 200 Hz  -

Part Number Nominal Diameter Connection size L B H H1
(mm) (mm) (mm) (mm) (mm)
8288200.96XX 15 G 1/2 65 55 147 134
8288300.96XX 20 G 3/4 95 70 164 140
8288400.96XX 20 G 1 95 70 164 140 

Write a review

Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below: