Bettis Actuator

Key Features Smallest footprint to torque ratio Compact and concentric design Balanced helical design eliminates side loading on valve assembly  and stem. High water ingress protection – IP68 Integrated “crossover” valves (Double-acting) Vibration resistant design. Easy adaption to standard valve bonnet design Unlimited mounting positions with built-in position adjustment Design ready to accept a wide selection of control modules Five Year Warranty – The BHH actuators are backed by the industry's strongest materials and workmanship warrant Working pressure 100 – 207 Bar /  1500-3000psi Torque output : 30Nm/250lb-in to 16000Nm/141000 lb-in  at 207Bar / 2000psi Test pressure: 1.5x working pressure  to a maximum of 250 Bar / 3600 psi Temperature range: -20c to +80c / -5F to +180F Standard 0c to +120 / 32F to +250F (option) -50c to +60c /  -58F to +140F (Consult factory) Viscosity of hydraulic oil : 15 to 200 cSt BHHF single acting : 100Bar/1500psi and 135Bar/2000psi spring set available

Key Features Water Ingress Protection to meet both IP66 and IP67M specifications for submergence and severe high pressure water testing NAMUR Topworks allow standardization of accessory hardware and the direct or close coupling of NAMUR designed hardware and accessories Quad Sealed Torque Shaft, the lower torque shaft has two independent seals – the outer seal protects the large bearing area and the primary, inner cup seal from the environment. The upper shaft bearing area features a bi-directional, double lip seal providing twice the level of protection from corrosion and contaminants O-Ring Sealed Cylinders essentially eliminate the possibility of any cylinder leakage throughout the full range of operating and climatic conditions Standard Accessory Mounting Pad is identical on all CBA-300 and CBA Series models allowing the panel mounting of controls Piston Heel and Yoke Pin Bearings manufactured from PTFE/bronze help ensure smooth and consistent torque output and increase total cycle life Totally Enclosed Body provides complete protection of all internal moving parts and minimizes the chance of injury to operating personnel  The Scotch-Yoke Mechanism tran

Key Features New Dual O-Ring seal on each end of the torque shaft restrict external contaminants, providing a high level of corrosion and water resistance O-Ring Sealed Cylinders essentially eliminate the possibility of any cylinder leakage throughout the full range of operating and climatic conditions Standard Accessory Mounting Pad is identical on all CBB and CBA-300 Series models allowing the panel mounting of controls Piston Heel and Yoke Pin Bearings manufactured from PTFE/bronze help ensure smooth and consistent torque output and increase total cycle life Totally Enclosed Body provides complete protection of all internal moving parts and minimizes the chance of injury to operating personnel  The Scotch-Yoke Mechanism transforms linear movement of the piston into a 90 degree rotating movement, providing optimum start or end torque  Center Bar, made of high strength alloy steel, guides the piston throughout its full stroke, preventing metal to metal contact with the cylinder bore  Bi-directional Travel Stops are an integral part of the actuator allowing 80° to 100° total travel adjustment. Extended travel stops are optional  Critical Be

Key Features Splined Drive Inserts – The D-Series blowout-proof shaft is fitted with changeable inserts for universal mounting to a wide variety of valves without the need for brackets or couplings. Corrosion Resistance – As standard, an exclusive two-component polyurethane epoxy coating, in conjunction with a fully anodized housing and dichromated pistons, provides the D-Series actuators with a highly corrosion resistant surface. Coupled with all 304SS fasteners, the D-Series provides excellent protection from hostile environments. BettisGuardTM – For the most hostile applications, BettisGuardTM adds the highest practical level of corrosion protection by impregnating the body and end caps with a ceramic filled fluoropolymer-based epoxy resin and aluminum pinion gears (BGA). As a further option we can supply stainless steel pinion gears (BGS). Three-Point Suspension – D-Series pistons feature a unique three point suspension system. Each piston has three wide, machines load fingers strategically located about the rear circumference of the piston. These load fingers counteract the piston/rack side loading and prevent the natural tendency of

Key Features Wear Resistance - The G-Series Powr-Swivl piston rod connection is contained by the guide block, which is supported by a high strength alloy steel reaction bar treated to provide a highly corrosion and wear resistant finish. The Powr-Swivl, superior surface finishes, and self-lubricating bearings maximize the transfer of input energy directly to the valve stem. The tension loaded spring minimizes radial loads on the piston rod, further enhancing efficiency Service Rated - G-Series models are qualified by accelerated wearage testing. The actual service life may be predicted based upon specific application parameters and environmental conditions. Proper actuator selection, enhanced by proprietary data analysis methods, allows optimum performance and operating economy Replaceable Bearings - Low friction, permanently lubricated, high performance bearings protect sliding and rotating components, significantly extending actuator life Five Year Warranty - G-Series actuators are backed by the industry's strongest materials and workmanship warranty Corrosion Resistance - G-Series actuators incorporate protective

Key Features Rotary & Linear Readily adaptable to all rising stem valves Direct connection to valve stem Standard temperature range from -50F(+65C). For other temperature requirements, consult factory Materials of construction to suit process and ambient conditions Adaptable to "NACE" trim valves (MR-01-75); suitable for operation with sour power gas on application Piston with non-metallic wear ring to prevent piston/cylinder scuffing Zero leakage piston and rod seals; material to suit application Suitable for 1480 psig (102 barg) maximum working pressure for tank diameters NPS 8 or less; higher pressure on application Suitable for 1450 psig (100 barg) maximum working pressure for tank diameters NPS 10 or greater; higher pressure on application Complete control packages featuring rugged Bettis™ poppet style relays to suit specific application Full pressure control packages available for use where specifications disallow regulators Manual pump for emergency operation Manifold controls are fully enclosed and weather protected by lockable cover Special locking valve

Key Features Pneumatic to 150 psig and 42" diameter Hydraulic to 2000 psig and 22" diameter Double Acting Spring Return - Fail Open or Close Double Acting Thrusts to 500,000 lbs Spring Return Thrusts to 50,000 lbs Bettis™ GVO-Series linear operators have been designed for service in safety shutdown and control applications. There are six basic models that address low pressure or high pressure operation and double-acting, spring-return or fail-safe configurations. Double-acting models are adaptable to any type of gate valve and have cylinder sizes ranging from 3 inches through 36 inches. They come with optional jackscrew manual overrides and materials of construction for special applications. Spring-return models are adaptable to direct or reverse acting gate valves, API or ANSI and have cylinder sizes ranging from 8 inches through 36 inches. High pressure models are suitable for 2000 psig hydraulic service. Typical Applications Automation of all rising stem type ball and gate valves

Key Features The HD-Series double-acting actuators are available with guaranteed minimum output torques to 50,331 lb-in (5,687 Nm). Fail safe spring-return models produce guaranteed minimum spring ending torques to 18,044 lb-in (2,039 Nm) The HD-Series operates at pneumatic pressures up to 250 PSIG (17 BAR) or hydraulic pressures up to 3000 PSIG (207 BAR).  Consult factory for hydraulic applications Bettis™ HD-Series hydraulic actuators are ideally suited for operating ball, butterfly, plug valves, dampers and other 90 degree turn devices. The HD-Series actuators provide a practical and reliable method for opening and closing valves by remote control without the need for expensive and unnecessary gearing, hydraulic pumps or other motor driven devices. Typical Applications Automation of ball, butterfly and plug valves Automation of louvers and dampers Automation of any quarter-turn mechanism

The Series 2000 electric valve actuator offer a wide range of frame sizes, horsepower ratings, and output speeds readily tailored to your specific applications.  The Series 2000 Quarter Turn electric valve actuator offers a wide range of frame sizes, horsepower ratings and output speeds BETTIS quarter turn products are selected by application requirements of voltage, torque, operating time, and valve shaft diameter. Actuators are designed tor ball, plug, and butterfly valves as well as quarter turn damper and louver drives. The Series 2000 Multi-turn electric valve actuator products are selected by application requirements of voltage, torque, thrust, RPM, and stem or shaft diameter. Actuators are designed for service on gate, globe, check , stop-check, and angle-check valves as well as sluice gates, weir gates, and multi-turn damper drives.   M2CP Modular Control BETTIS M2CP modular control package has been specifically designed to provide users a highly flexible, reliable, and competitively priced control system for electric valve automation. Through its unique design concept, servicing and upgrading can easily be accommodated.

Multiport Actuator - MPA  The Multiport Actuator (MPA) is an electronic system specifically designed to control and monitor the operation of the Multiport Flow Selector. It combines an exclusive solid state motor starter with control software to provide precise positioning of the Multiport Flow Selector within +/- one degree of the selected port, retaining that position even in the event of a power loss. The MPA provides configurable port selection from 3 to 8 ports.  The MPA allows user to select any port as home port or skip any unused ports.  This actuator allows for field torque adjustment while protecting the Multiport Flow Selector from excessive torque. The MPA stores alarm history to detect abnormal operating conditions for preventative maintenance of the MPFS and the MPA.   The Multiport Actuator interfaces with industry standard network communication protocols. The MPA is designed to operating in harsh and hazarious environments.  The MPA provides manual override upon loss of power. The actuator is capable of working with a wide range of voltages - three-phase, single-phase and DC.

The PCS system accepts a 0-10 VDC or 4-20 mA analog command signal.  This signal is used by the PCS to move the actuator's rod or rotational shaft to move to and hold a specific position.  The PCS is designed to control any pneumatic Bimba position feedback cylinder, including PFCN, PFCNL, PFC, PFCL, and PTF series actuators. Operating Pressure:  70 to 80 PSI Reverse polarity and overvoltage protected Flow rated models:  0.02Cv, 0.04Cv, 0.08Cv, 0.10Cv, 0.11Cv, 0.25Cv Options:  No enclosure, quick connect Requires 24V DC Power Generates 10V DC to energize resistive probe

The PressureGuard™ Self-Contained Hydraulic Emergency Shutdown Systems are designed to provide reliable valve shutdown capability when an external power source is either not available or not dependable. The PressureGuard system has proven to be highly successful in years of field service under some of the most demanding operating and environmental conditions. The module can be used with either rotary or linear spring-return hydraulic operators to provide a fail-safe system adaptable to ball, plug and other quarter-turn valves as well as reverse-acting gate and other linear operated valves. The PressureGuard system offers built in temperature compensation and pressure relief. It provides the foundation for a flexible system utilizing a variety of available sensing and control options. Typical Applications Emergency valve shutdown Surface safety valve control Any application in which no plant air or hydraulic supplies are available Key Features Suitable for remote, unmanned, unpowered and critical service Adaptable to either quarter-turn or linear operated valves Field-proven in extreme climatic conditions Stan

Key Features The E-Series range of quarter turn actuators incorporates special materials of construction, such as lightweight aluminum drive cases and filament wound fiberglass cylinders (pneumatic). As well, these actuators do not use brass or bronze components making them ideal for sour service conditions.   The E-Series actuators are available in several ambient temperature ranges. Standard temperature range: -50º F to +150º F Extreme low temperature range: -65º F to +150º F Moderately high temperature range: -20º F to +225º F     The E-Series actuators operate at pneumatic pressures up to 150 PSIG (10 BAR) or hydraulic pressures up to 2000 PSIG (138 BAR). Bettis™ E-Series pneumatic and hydraulic actuators are particularly well suited for operating ball, butterfly, plug valves, dampers and other 90 degree turn devices. The E-Series actuators provide a practical and reliable method for operating valves via remote or automatic control by incorporating a variety of field proven control accessories. An actuator and control system package can be custom designed for each specific

When we created the TEC2000 we didn’t reinvent the wheel. Instead of devising a completely new actuator, we simply equipped our well-established Series 2000 actuator with all the features needed to offer Total Electronic Control (TEC) in a truly non-intrusive package. This means that with the TEC2000, you get the latest standards of control and performancecoupled with power transmission technology that has a 30-year history of reliability inthousands of installations worldwide. The Series 2000 heritage ensures that the TEC2000 isan electronic actuator that’s built for hard work and easy maintenance. Quarter-turn and multi-turn control in one truly non-intrusive actuator The TEC2000 series can handle both quarter-turn and multi-turn applications across anextremely broad torque range—using either three-phase or single-phase power.  While some manufacturers claim to offer non-intrusive actuators, take a closer look at theirproducts. You’ll discover electric control compartments that have to be opened to replace fuses (which defeats the purpose of non-intrusiveness, and can even void some manufacturers’ warranties). BETTIS TEC2000 is tr

Bettis’ TorqPlus electric valve actuators employ a unique modular design to allow for simple retrofits/upgrades using over two hundred different kits including heaters and thermostats, single or dual-potentiometers, servo controls, motor brakes, positioners and transmitters to name just a few. All actuator components can be added inside the NEMA 4 or NEMA 4 and 7 rated housings. Typical Applications Automation of ball, butterfly and plug valves Automation of louvers and dampers Automation of any quarter-turn mechanism Key Features Guaranteed output torques from 140 lb-in to 10,000 lb-in  (16 Nm to 1,130 Nm) Female DIN/ISO available for direct valve mounting CSA certified enclosures are offered in both a non-hazardous (type 4) and  a combination non-hazardous plus hazardous (type 4 & 7) construction Modular design allows an almost endless possibility of control options and field modifications Operating speeds are available from 4 seconds to 60 seconds per 90° rotation Operating temperatures range from -40°F to +140°F (-40°C to +60°C) Compact design provides a maximum output torque in the smallest package