Apollo actuator

American-Made Success Since 1928 Conbraco Industries was created when two Detroit-based manufacturers of brass valves and fittings merged in 1928 forming Consolidated Brass Company. Over 80 years later, Conbraco is an American success story that's still being written. The company now known as Apollo® Valves earned a reputation for developing new products to meet emerging market demands. In 1968, the company introduced its Apollo® Series 70 ball valve to the commercial market. A revolutionary innovation at the time, the product became the most specified ball valve in the world. Line extensions have resulted in new materials, new sizes and new applications for the classic Apollo ball valve. In 2005, the company brought all of its products under the Apollo® Valves brand. Products which had been sold under the Conbraco brand included plumbing and heating products, water gauges, pop safety and relief valves, marine fittings and backflow prevention devices. Those lines joined the company's ball valves, actuators and mixing valves as part of the complete Apollo Valves family of products.

Product Compare (0)

Apollo actuator Models A0025-A4000

FEATURES 1. Cast Aluminum Body Yellow Chromate Coated Polyester Powder Coat Finish 2. Die Cast Aluminum End Caps Yellow Chromate Coated Polyester Powder Coat Finish 3. Die Cast Aluminum Pistons Yellow Chromate Coated 4. Aluminum Alloy Pinion 7075-T6 Hard-coat Anodized Finish 5. Drive Inserts Extruded Aluminum Hard-coat Anodized Finish 6. Preloaded Concentric Springs Deltatone® Coated 7. Piston Guides Molybdenum Disulfide filled Polyamide 8. Bushings Polyoxymethylene (POM) 9. O-Ring Seals Standard Temp. (-4°F to 180°F): Buna-N High Temp. (-4°F to 250°F): Fluorocarbon Low Temp. (-40°F to180°F): Silcone 10.Capscrews, Nuts & Othe

Apollo AE series electric actuator

Five Output Torques, One Housing • 200, 400, 600, 800 and 1,000 inch-pounds • Long Service Life • Newly developed anodized die cast aluminum housing • Fiberglass reinforced nylon cover resists corrosion • Nitrile gasket and seals cover all penetration points in housing and cover • Precision cut and heat treated alloy spur gears • Permanently lubricated enclosed gear train • NEMA 4, 4X Easy To Use • Two separate 1/2” NPT conduit entrances for easier wiring and signal separation • 12-position pre-wired terminal strip includes standard connections for remote open/closed position indicators; lots of room for wiring options • Unrestricted mounting orientation • Built-in thermal overload protection in all AC motor actuators • Limit switches have an 11 amp rating at 115 VAC • High visibility valve position indicator standard on all models Many Standard Features • Stainless steel push-and-turn manual override shaft, position indicator shaft and female output • ISO 5211 F07 drive output reduces inventory of mounting kits • 115 AC & 220 AC models feature a 25% duty cycle below 100˚F &nb

Apollo CS&CL Series electric actuator

- Features- • Plug-in connectors for the motor, the brake option and the heater/thermostat option • All connectors are coded to prevent mis-wiring. • Limit switch wires are soldered to the board - no more loose connections. • A six position terminal strip clearly labeled so it can be wired up in the field without an instruction manual. Introducing Simplicity for Calibrating Modulating Actuators The Control Board brings a whole new level of simplicity to the field. It will work with either of the Motor Boards (115VAC or 230VAC). Features include: • Switch selector for 4-20mA or 0-10VDC input • Switch selector for 4-20mA or 0-10VDC position readback • Switch selector for either “fail in-place” or “fail to zero” upon loss of control signal (provided input power remains) • On-board push buttons to manually position the actuator • An adjustable pot for Speed Control (motor pulsing) • An adjustable pot for deadband adjustment • A “Mode Selector” switch with LEDs, which are used for: • ”No tools” pot calibration • Setting Zero and Span • Manually positioning the actuator • Locked Rotor Protection if the actuator cannot achieve the position comman

Apollo G series actuator

Spring return or double acting, quarter turn, scotch yoke actuators. Torque ranges from 10,000 in.lb. to +22,000 in. lb. NAMUR The shaft driven accessory interface conforms to the NAMUR standard and is identical on all G-Series actuators, allowing for standardization of accessory mounting hardware and installation practices • Pneumatic and hydraulic scotch-yoke actuators • Automates ball, butterfly, plug valves and any other 90° rotating mechanisms • Salt Spray Testing per ASTM B117 criteria. Construction features prevent water ingress, allowing G-Series actuators to meet IP 66 and IP 67M specifications and severe high pressure water deluge test • Operating Ranges G-Series double acting actuators produce guaranteed minimum torque outputs from 10,000 lb-in. up to 6,000,000 lb-in. The spring return units produce spring torques from 2,500 lb-in. to 3,000,000 lb-in. • Standard operating pressures: Pneumatic — to 200 psig (14 BAR) • Standard operating temperature is -20°F to +200°F (-29°C to +93°C) Optional trims available: 0°F to +350°F (-18°C to +177°C) -50°F to +180°F (-46°C to +82°C) • Mechanical and hydraulic manual overrides are available • MSS and ISO Valve Mounting The G-Series

Apollo LB Series electric actuators

The LB-Series is available in several basic designs with a wide variety of configurations from which to select torque and speeds to meet specific application requirements. These rugged and uncomplicated actuators provide a practical and reliable method for turning any mechanism 90˚. Torques range from 540 inch-pounds to 54,000 inch-pounds (6.25 to 625 kilogram-meters). Electrical models are available in 115 VAC-50/60 Hz single phase, 200 VAC-50/60 single phase; and 220/440 VAC-50/60 Hz three phase. Models are available for on/off modulating control. LB Series Electric Actuator Performance Data Actuators and Controls L-B Series Torque Rotating Speed Power Requirements 30% Duty Cycle Model Output (Sec/90 degree) 115VAC 1 Ph 60Hz 460 VAC 3 Ph 60 HZ Number Lb-In Std Opt RATED START RATED START OA8 885 5 1.95 3.3 0.63 1.15 OA8 885 25 1.25 2 0.39 0.78 OA15 1350 15 25 1.95 3.3 0.39 0.78 AT25 2250 15 1.95 3.3 0.63 1.15 AT25 2250 25 50 1.95 3.3 0.39 0.78 AT50 4500 25 4.6 12 0.63 1.15 BT100 10600 50 4.6 12 0.63 1.15

Apollo Rack and Pinion actuators

Apollo Spring return or double acting, stainless steel, quarter turn, rack and pinion actuator.

1. Investment Cast Body Assures manufacturing of other special alloys, such as Monel 2. Unique Drive Pinion One piece stainless steel alloy shaft, precision machined gear and teeth for precise control 3. Bearings Replaceable top and bottom TFE Pinion Bearings to ensure low friction, stability above 400°F, and chemical resistance 4. Travel Stops Provides +/-4° travel adjustment in outboard direction 5. Accessory Mounting Manufactured to NAMUR to provide international standardized mounting 6. Stainless Steel Pistons Precision cast pistons are guided through full face engagement with the pinion and piston guide 7. NAMUR Slotted Shaft Standard to provide a self-centering positive drive for positioners, a variety of switches 8. Actuator Mounting Manufactured in accordance with ISO 5211 to ensure mounting the actuator directly on valves 9. Pre-loaded Cartridges Converts a standard double acting actuator to a spring return unit by simply removing the end caps and adding the spring cartridges 10. NAMUR Solenoid Mounting International standard for direct mounting of solenoid valves

Showing 1 to 7 of 7 (1 Pages)