Minimized design attaching importance to its compactness.
The dimension is same with 160S-1 series except the part of sensor which fixed at the head side.
Position sensor is usable under strong magnetic field where general magnetic sensor cannot be used.
 |
Product Lineup |
  Click the icon as follows, to check the details. |
|
| Structure |
Series |
Mounting Style |
Bore Size mm |
| 32 |
40 |
50 |
63 |
80 |
100 |
125 |
| Double-acting Single-rod |
Standard Type |
SD |
|
|
|
|
|
|
|
| FA |
|
|
|
|
|
- |
- |
| LA |
|
|
|
|
- |
- |
- |
|
|
|
Specifications |
|
| Series |
Double-acting Single-rod/Standard Type |
| Available Bores(mm) mm |
 32·40·50·63·80·100·125 |
| Mounting Style |
SD·LA·FA mounting |
| Nominal Pressure |
16MPa |
| Max. AllowablePressure |
16MPa |
| Proof Test Pressure |
24MPa |
| Min. WorkingPressure |
0.3MPa |
| Operating Speed Range |
8∼100mm/s |
| Note1)Temperature Range |
-10∼+100ºC(But do not use when frozen) |
| Structure of Cushioning |
None |
| Adaptable Working Oil |
Petroleum-basedFluid
(For other working oil, refer to the table of working oil adaptability.) |
| Tolerance of Thread |
JIS 6g(/6H) |
| Standard Stroke |
5·10·15·20·25·30·35·40·45·50
(For more than 65 stroke, please consult with our sales) |
| Stroke Tolerance |
0∼0.8mm |
| Rod End Thread |
Note2) Male Thread |
| Note1) |
The sensor may not be damaged at temperature over 60ºC, but the accuracy may be lost. |
| Note2) |
As the sensor is built inside the piston rod, it is not available for female rod end thread. But it may be possible depending on the bore and stroke, ,please consult with our sales. |
|
Specifications of detecting device |
|
| Power |
DC12∼24V±10% ripple 10% and below |
| Consumption current |
30mA and below |
| Accuracy |
Note1)Repeatability |
±0.1%FS and below |
| Linearity |
±1%FS and below (ambient temperature) |
Temperature Character
(temperature drift) |
±1%FS and below(at0∼+60ºC): at the part of amplifier
±2%FS and below(at0∼+60ºC): at the part of sensor
±10%FS and below(at0∼+100ºC): at the part of sensor |
| Note2)Output |
1∼5V (at the piston retracted end : 1V) |
| Response |
4kHz(-3dB) |
| Temperature Range |
-10∼+100ºC: part of sensor
-10∼+60ºC: part of amplifier
(But do not use when frozen) |
| Impact-resistant |
500m/s2 X,Y,Z ; 3 times at every direction |
| Note3)Water-resistant |
Sensor : Equivalent to IP66 Amplifier : without any protect |
| Wiring |
Between sensor and amplifier : 3-cores4 2m
Amplifier ∼:4-cores2m without treatment at one side. |
| Note1) |
The variation in output is measured on a same basis (viscocity, power supply voltage etc.) at same position. |
| Note2) |
The output of sensor at the rod end is various depending on the cylinder stroke. Please check the output diagram of sensor. |
| Note3) |
The water-resistant will get worst when high temperature. Please take notice when using at the time of cleaning. Do not installed the amplifier at the place where may splashed with water and dust. |
|
Allowable Fluid, Seal Material |
| Type |
Working fluid |
Petroleum-based
Fluid |
Water-Glycol
Fluid |
Phosphate-Ester
Fluid |
Water in Oil
Fluid |
Oil in Water
Fluid |
| 3:Fluoric rubber |
 |
|
|
|
|
| 6:HNBR |
 |
|
|
|
|
| Note1) |
The -marked items are applicable,while the -marked items are inapplicabe. |
| Note2) |
The -marked items are the recommended packing materials in case of giving the first priority to abrasion resistance. |
|
Product Composition |
 |
