Burkert valve Water and other neutral media Type 0330 - Direct acting pivoted armature solenoid valve
2/2 or 3/2-way Solenoid Valve,
with pivoted armature and
isolating diaphragm
Lockable manual override as standard
For liquid, gaseous and aggressive media
Long service life, even in non-lube conditions
Insensitive to contaminated fluids
Analysis version available
Technical data
(G 1/8, NPT on request)
G 1/4
Port connection
DN 2.0 - 4.0
Ori ce
Brass and stainless steel 1.4401
Body and seat materials
Epoxy
Coil material
H
Coil insulation class
NBR and FKM (EPDM, FFKM on request)
Seal material
Media
Neutral media, such as compressed air, water,
NBR
hydraulic oil
Hot air, oxygen, hot oil, per-solution
FKM
Oil and fat-free media
on request EPDM
Hot air, oxygen, hot oil, per-solution
on request FFKM
Media temperature
0 to +80 !
NBR
0 to +90 !
FKM
-30 to +90 !
on request EPDM
+5 to +90 !
on request FFKM
max. +55 !C (min. temperature see media temp.
Ambient temperature
2
/s
max. 37 mm
Viscosity
24 V DC, 24 V/50 Hz, 230 V/50 Hz
Operating voltage
further on request
!10
Voltage tolerance
100% continuous rating
Duty cycle
Cable plug Type 2508 (DIN EN 175301-803 Form A)
Electrical connection
for 7 mm cable (supplied as standard)
IP 65 with cable plug
Protection class
0.47
Weight [kg]
As required, preferably with actuator upright
Installation
Technical data C Analysis versio
Solenoid valve for higher requirements
Media owing through is not contaminated, for pure
Analysis version
This version is particularly suitable for switch-
media
ing from extremely pure gaseous and liquid
2
< 0.2 mg/dm
Carbon residue threshold
media. All contaminated parts are subjected
-4
mbar l/sec
10
Permissable leakage rate
to additional puri cation processes, so that the
neutral / aggressive Media, which do not attack the
Media
media is not under any circumstances con-
body and seal material
taminated. The assembly takes place under
technical vacuum
cleanroom conditions.
Tag connector acc. to DIN EN 175301-803 A
Electrical connection
(previously DIN43650) for cable plug Type 2508
Tightness tested on helium leak detector,
-4
(see accessories)
mbar I/sec.
10
No oil, fat or silicon used whatsoever in mounting
Mounting instruction
Ordering chart for valves, analysis and vacuum version (other versions on request)
Stainless steel body, seal material FKM or NBR, manual override and without cable plug (see Accessories)
Kv value water Pressure Item no. per voltage/frequency
3 1) 4) 2)
[m range [bar] [V/Hz]
/h]
ce [mm]
Circuit function Port connection threaded port Ori Seal materialDC AC (DC) 024/DC 024/50 230/50
Analysis version
3)
Stainless steel body
A 2/2-way valve NC
G 1/42.00.080.11Vac. -10FKM137 839C137 84
3.00.140.18Vac. -6 137 843C137 84
4.00.170.23Vac. -3 122 101C137 84
Stainless steel body
universal
T 3/2-way valve,
function, any ow direction
G 1/42.00.080.11Vac. -8FKM137 850C137 85
3.00.140.18Vac. -5FKM137 855C137 85
4.00.170.23Vac. -3FKM137 859C137 86
Cable plug acc. to DIN EN 175301-803 Form A
Fixing screw
Circuitry Voltage / frequency Item no.
Flat seal
None (standard) 0 - 250 V AC/DC008 376
The delivery of a cable plug includes the at
with LED 12 - 24 V AC/DC008 360
seal and the xing screw. For other cable
with LED and varistor 12 - 24 V AC/DC008 367
plug versions acc. to DIN EN 175301-803
with recti er, LED and varistor12 - 24 V AC/DC008 363
Form A (previously DIN 43650), see data-
with LED 200 - 240 V008 362
sheet Type 2508.
with LED and varistor 200 - 240 V008 369
further versions see datasheet Type 2508
Write a review
Your Name:Your Review: Note: HTML is not translated!
Rating: Bad Good
Enter the code in the box below:
